Orders >$15 will ship with full tracking from the US to domestic destinations and USPS ePacket countries (most of Europe, Brazil, Russia, Japan, South Korea, Singapore, Hong Kong, Israel, Australia, New Zealand).

Shared boards by: NStorm

Search shared boards:
Autolight-board

Autolight-board

Created by NStorm on 2019-05-28 10:01:54

2 Layer Board - 0.5351 sq in (0.8120in x 0.6590in) / 345.23 sq/mm (20.62mm x 16.74mm)
$2.14 per set of 4 ($4.00 per sq in)

Auto light

Attiny10 & APDS-9930 based automatic light/switch

https://github.com/N-Storm/autolight

https://easyeda.com/NStorm/autolight-board

This project utilizes small ATtiny10 mcu to work with APDS-9930 ambient light (AL) and proximity I2C sensor.
This is used for automatic "smart" light in a drawer. Once the drawer are open the APDS-9930 will notice proximity change
and trigger a preset interrupt and MCU will come from sleep to check if AL level are below set (i.e. it's dark around).
If the set condition for AL level will be met, it will enable HIGH level on PB3 pin. Which is connected to a MOSFET or any other switch to enable LED light.

Reset shares same PB3 pin so it must be disabled via fuses. You will have to apply +12V to PB3/RESET pin to reprogram attiny10 after flashing RSTDISBL fuse.

The PB2 port are used as INT0 for sensor interrupts to wake MCU from sleep on proximity change event.

Building

Fetch the latest trunk:

git clone https://github.com/N-Storm/autolight && cd autolight

Then tweak some settings in autolight.h if required. They are commented. After that do a:

make && make flash && make fuse.

:warning: After you do a make fuse step, you won’t be able to program MCU again without applying +12V to RESET pin (make sure it’s not connected to your programmer hardware :warning:

Alternatively you can use pre-built binaries with the default settings from releases section.

Connecting

PB0 ↔ SCL

PB1 ↔ SDA

PB2 ↔ INT

PB3 are the module digital output, with logic LOW when light should be turned off and HIGH when it should be on. Suited for connecting to an N-channel FET driving the LED light.

Please be aware that the APDS-9930 module requires 2.5 – 3.6 V for it’s operation on Vdd+Vbatt (IR LED power). I recommend to use a 3.3V LDO for powering both MCU & APDS-9930.

Schematics & board are available on EasyEDA: https://easyeda.com/NStorm/autolight-board

:warning: This board has two places for LDOs - U3 & U4. Solder only one of them! :warning:

They replace each other. The board are made so they could replace each other. Alternatively edit board/schematics to replace them with your favorite LDO.

This project utilizes software I2C library by eXtreme Electronics, India.
www.eXtremeElectronics.co.in

License: CC-BY-SA 3.0
Project URL: https://github.com/N-Storm/autolight
Tags: avr, attiny, attiny10, light, home automation

3 people have said "Thank You" for this board.

Say "Thank You"



Order Now

Top View - Complete Board

Top View - Complete Board

This is what your finished board will look like from the top.

Bottom View - Complete Board

Bottom View - Complete Board

This is what your finished board will look like from the bottom.

SOT23-6 DIP adapter v2

SOT23-6 DIP adapter v2

Created by NStorm on 2018-07-27 07:41:02

2 Layer Board - 0.1240 sq in (0.4000in x 0.3100in) / 80 sq/mm (10.16mm x 7.87mm)
$0.50 per set of 4 ($4.00 per sq in)

SOT23-6 adapter / breakdown board
Variant 2

License: CC-BY 4.0

1 person has said "Thank You" for this board.

Say "Thank You"



Order Now

Top View - Complete Board

Top View - Complete Board

This is what your finished board will look like from the top.

Bottom View - Complete Board

Bottom View - Complete Board

This is what your finished board will look like from the bottom.

SOT-23 DIP adapter

SOT-23 DIP adapter

Created by NStorm on 2018-07-27 07:32:05

2 Layer Board - 0.1521 sq in (0.3900in x 0.3900in) / 98.13 sq/mm (9.91mm x 9.91mm)
$0.61 per set of 4 ($4.00 per sq in)

SOT23-6 adapter / breakdown board

License: CC-BY 4.0

1 person has said "Thank You" for this board.

Say "Thank You"



Order Now

Top View - Complete Board

Top View - Complete Board

This is what your finished board will look like from the top.

Bottom View - Complete Board

Bottom View - Complete Board

This is what your finished board will look like from the bottom.

EFM32TG222F32 Board

EFM32TG222F32 Board

Created by NStorm on 2018-05-02 11:39:56

2 Layer Board - 3.2361 sq in (1.6100in x 2.0100in) / 2087.8 sq/mm (40.89mm x 51.05mm)
$12.59 per set of 4 ($3.89 per sq in)

EFM32TG222F32-QFP48 Simple Dev Board

The schematics are based on the AN0002: Hardware Design Considerations standard decoupling. No advanced AVDD filtering applied. This board was designed without analog signal separated from digital part. So the analog part of this board might be noisy. I don't have analog parts in my project so this wasn't considered.

Vin goes through onboard optional LDO. Vcc are LDO output / directly applied to MCU.
Optional LDO (U3) are MIC5219-3.3BM5.
X1 are high freq oscillator. X2 are optional low freq oscillator.

Parts list (BOM):

C1,C2,CVDD,CAVDD,CIOVDD: 10uF, 0603
CVDD: 1uF, 0603
CVDD1,CIOVDD_0,CIOVDD_3,CIOVDD_5: 0.1uF, 0603
CAVDD_0,CAVDD_1: 10nF, 0603
C3,C4: 22pF, 0603
C4,C5: 33pF, 0603
C7: 470pF, 0402 (LCSC: C117605)
R1: 470 Ohm, 0402
R2,R3,R4,R5: 0 Ohm (can be soldered), 0402
R6: 10K Ohm, 0201
LED1: 0603 LED
U1: EFM32TG222F32-QFP48
U3: MIC5219-3.3BM5
X1: Quartz up to 32MHz HC49S (LCSC: C24625)
X2: Quartz 32kHz 2-SMD (LCSC: C182057)

License: CC-BY-SA 3.0
Tags: efm32, mcu

1 person has said "Thank You" for this board.

Say "Thank You"



Order Now

Top View - Complete Board

Top View - Complete Board

This is what your finished board will look like from the top.

Bottom View - Complete Board

Bottom View - Complete Board

This is what your finished board will look like from the bottom.

SI705x/702x/7006 Minimal Board

SI705x/702x/7006 Minimal Board

Created by NStorm on 2017-06-27 14:57:01

2 Layer Board - 0.2397 sq in (0.5100in x 0.4700in) / 154.64 sq/mm (12.95mm x 11.94mm)
$0.96 per set of 4 ($4.00 per sq in)

Minimal breakout board for Silicon Labs SI705x/SI702x/Si7006 I2C temperature / temperature + humidity sensors.

This board does not includes any sort of voltage regulator. Make sure to supply correct Vcc (1.9 to 3.6 V) for this board. Connecting directly to 5V MCU (like Arduino without 3.3 V voltage regulators) will burn this sensor. This is a minimal circuit from "Typical Application Circuit" section from the datasheet.

Parts list (BOM):

R1-R2: Resistor, 10 k, ±5%, 1/16 W, 0603
C1: Capacitor, 0.1 μF, 16 V, X7R, 0603
U1: Si705x/702x/7006 sensor, DFN6.

Tested to work with Si7051 high accuracy temperature sensor, reading data with Arduino.

License: CC-BY-SA 3.0
Project URL: https://easyeda.com/NStorm/SI705x_Minimal_Breakout_Board_copy-8b5dbeb7044540c8a46320b8b4c4fd84
Tags: temperature, enviromental, sensor, silicon labs

1 person has said "Thank You" for this board.

Say "Thank You"



Order Now

Top View - Complete Board

Top View - Complete Board

This is what your finished board will look like from the top.

Bottom View - Complete Board

Bottom View - Complete Board

This is what your finished board will look like from the bottom.